[yanax]

You were right Dan.
I reversed the connection of my brown wire with red and everything works.
Which gives me black on red and red on brown and finally white on orange.

Thank you so much.

[yanax]

Hello Rob,
Thank you for the answers.

I have test the Pen Up / Down under Manual Driving in the Makeangelo software. But the sevo motor does not work.

Is it possible Rob that you put me a picture of your connection red white black with yellow brown and red?
I try your Angle.
#define PEN_UP_ANGLE (180)
#define PEN_DOWN_ANGLE (140) // Some steppers don’t like 0 degrees

Thank you,
Yanax

[yanax]

Thank you Dan,
I use your Makelangelo 3.2.
So I have a white red black connection.
If I understand correctly, I have to connect the red of my new servomotor to the black of your connection.
And the brown of the new servomotor on the red. Its good?
And I still have the yellow that will go on the white?

[yanax]

when I connect the cable to the servomotor, it is impossible to test the movement by the program of the pc.I am well connected.But the servomotor does not move.j’en is tested a second and it’s the same

[yanax]

Thank you for your generosity.

I will test the printing of M5 printer parts. I have a Micro delta Rework for printing.
And thank you again for the publication of your DXF file

[yanax]

In fact it is mainly: 4 MECH-0077 m4e1 Makelangelo 4 motor mount.

[yanax]

Thanks again for all Dan.
I put you a visual of a drawing size A2.
And a little thing that improved the roaring.
I put Teflon.
I will make a more suitable frame.
It is possible to buy Makelangelo 3.2 Laser Cut Parts on your website.
Is it possible to buy the files instead? I would like to cut them out of thicker wood or pvc.

See you soon,

[yanax]

Good news.
It’s not perfect, but almost. I am on the right track. I unscrewed everything, including the notched wheel, one was not sere enough. Obviously the floor of the room where the machine is is not flat. I have everything upgraded. Maybe it was a swaying bottle. The return to the Home is not accurate. So I continue in this direction and I will give you a return.
Thanks again Dan.

[yanax]

20 teeth on mine

[yanax]

Hello Dan, excuse me for this late response.
Curiously the program was set to settings> pen> max speed = 6500, draw speed = 6500. I followed your advice and said settings> pen> max speed = 1000, draw speed = 1000.
You can see the result. It’s better. I put you an image with are back to the Home.
Looking at the machine working slowly, it is the belt that jumps apparently, which creates shift. Can you tell me if the gear is well placed?
Thank you

[yanax]

My last test was done with the actual size of my board 80 cm X 120 cm. Which does not change much of the board of your tutorial which is 84 x 122.

HELP!!!!!

[yanax]

For the bottom drawing, with the sharper lines, I put 250 g on the bottles. it’s not fluid on belts.
But in the end he never returns to the good home

[yanax]

yes it is the image c for the test. It’s not a mirror image. I am testing an A4 size letter size image.
I tested 2 12V 2Acest power supplies ok.
I tested A2 in A3, impossible in A4 too small apartment for the ficihier.
It’s discouraging ….
What is the ideal size of the board?

oui c’est l’image c pour le test. Ce n’est pas une image miroir. Je test une image A4 taille papier à lettre.
J’ai tester 2 alimentations de 12v 2Acest ok.
J’ai tester en A2 en A3, impossible en A4 trop petit appartement pour le ficihier.
C’est découragent….
Quelle est la taille idéal de la planche ?

[yanax]

Yes same problem. obviously when I move from right to left and from left to right the pencil never comes back to the same place.
Belts swerved on pulleys from time to time.
The 100g counterweights are hooked on the belt and move smoothly.
The motors are already very hot.
I do not touch the setting on the green circuit because I do not have a small screwdriver. And I want to be sure that’s fine.

Oui même problème. visiblement quand je bouge de droite à gauche et de gauche à droite le crayon ne revien jamais à la même place.
Les ceintures sautes sur les poulies de temps en temps.
Les contrepoids de 100 g sontaccrochés à la ceinture et bouge sans problème.
Les motors sont déjà très chaud.
Je n’est pas touché au réglage sur le circuit vert car je n’ai pas de tourevis assez petit. Et je veux être sur que c’est bien celà.

[yanax]

Thank you Dan for your responsiveness.
One curious thing is the coordinates of x and z before I had x0 and z 0.
Now I have the first picture.
Even by saying “This Home”.

Merci Dan pour ta réactivité.
Une chose curieuse ce sont les coordonné de x et z avant j’avait x0 et z 0.
Maintenant j’ai la première photo.
Même en lui dissant “This Home”.

[yanax]

The news are good.
Thank you very much Dan
The screen is displayed.
Obviously there are still a lot of curiosities.
In the control panel on the pc, when I ask him to go up sometimes he goes up then to the command after on the same button it goes down!
the driving brain of the pencil does not fit well, but I think I can adjust that in the settings. It’s almost always a little noise, but maybe it’s normal?
When I propose a file via the SD card it loads percentages, but does’t draw.
I’m doing tests and I’m coming back to you if I can not find a solution.

FR:
Les nouvelles sont bonnes.
Merci beaucoup Dan
L’écran s’affiche.
Visiblement il y as encore pas mal de curiositées.
Dans le paneau de contrôl sur le pc, quand je lui demande de monter parfois il monte puis à la commande d’après sur le même bouton il descend!
le cerveau moteur du crayon ne se possitionne pas bien, mais je crois pouvoir régler cela dans les paramètres. Il fait presque tout le temps un petit bruit, mais c’est peut-être normal?
Quand je lui propose un fichier via la carte sd il charge des pourcentage, mais ne dessine pas.
Je fais des tests et je reviens vers toi si je ne trouve pas de solution.

[yanax]

Merci Dan,
cela me fait travailler mon anglais c’est une bonne chose.
Je ne savais pas si tu étais francophone.

pour le moment je continus en anglais c’est mieux pour le forum.
Je fais la manipulation pour le fimeware dans l’heure qui vient.
😉

[yanax]

Thank you for your quick response as usual.
I am your instructions.
I give you news very quickly, but it’s 6 hours off …. I’m in France.
I feel you very caring.
Thank you

[yanax]

Hello Dan,
You have certainly delegated the manufacture to another person. For your information, the screws were not tight and I was obliged to fix the piece of wood that bore the metal mat for the pen.
And the power connector is impossible to properly screw, the nozzle is faulty.
It really does a lot!
Do you know why?
Occasionally I just want to operate your machine to which I have changed nothing.
Past Order: Order # 19319 (March 6, 2018)

I really feel that it’s firmware because when I connect the card to the program by pc, it is impossible for me to do any action.

How do I proceed?
Do I have to use the arduino program to transfer the firmware?
I have never done that.
thank you for your answer,

[yanax]

Sorry Dan, but the contrast wheel does not change squares into letters. It just changes their contrast.
I changed the connection.
Unfortunately still not functioning.
Is it possible that the firmware is not installed ?

thanks for your help

[yanax]

ok i change the connection.
I found them strange too. These are yours, I did not touch anything.
and I test the screen setting and make you a return.
Thank you

[yanax]

Thank you Dan.
This time it’s ok. it’s in English.
Thank you

[yanax]

it’s easy to open the jar file and explore it, but I can not find the language file to change. I delete the pig-latin language file, but it does not change anything.

[yanax]

Hello, sorry but I can not do anything. I install the software on another pc and there is no problem. I made a pasted copy of the file to replace it on the pc that has problems …. but nothing changes.
for the CMD, I tried to follow your request, but I did not succeed.

[yanax]

Thank you Dan,
The latest version does not change anything.
Can not run the .bat mod administarteur.
It’s strange because I have all rights admin on this pc.
when i try the bat say’s:

64 bit Windows
64 bit Java installed.
The current Java runtime is 1.8
finding the latest Makelangelo JAR…
File not found.
Appuyez sur une touche pour continuer…

[Author]

Posts